 |
Florida Administrative Code (Last Updated: December 2, 2024) |
 |
62. Department of Environmental Protection |
|
D62. Departmental |
|
62-701. Solid Waste Management Facilities |
1Specific references to the documents listed below are made throughout this chapter. These documents are adopted as standards and are incorporated into this chapter by reference. The reference documents are available for inspection at the Department’s district 38and Tallahassee offices, and may be obtained directly from the source49.
50(1) EPA document EPA/600/R-93/182, Quality Assurance and Quality Control for Waste Containment Facilities, September 1993.
65(2) 6640 C.F.R. Parts 61.149, 7061.150, 61.151, 61.154, Subpart M-National Emission Standard for Asbestos, July 1, 1992.
82(3) 8340 C.F.R. Part 136, 87Appendix B, Definition and Procedure for the Determination of the Method Detection Limit, revision 1.1; October 26, 1984.
105(4) Method 9095, Paint Filter Test, found in EPA document EPA SW-846, Test Methods for Evaluating Solid Wastes, Physical/Chemical Methods; Third Edition, September, 1986, as revised, December, 1987.
133(5) 134Methods 601 and 602, 13840 CFR Part 136, 142Appendix A, Methods for Organic Chemical Analysis of Municipal and Industrial Wastewater; December 22, 2000.
157(6) 15840 C.F.R. 258.13, 161Fault Areas: October, 1991.
165(7) 16640 C.F.R. 258.14, 169Seismic Impact Zones; October, 1991.
174(8) 17540 C.F.R. 258.15 178Unstable Areas; October, 1991.
182(9) 18340 C.F.R. 258, 186Appendices I and II; October, 1991.
192(10) 19340 C.F.R. 264 196subpart H, except for those sections specified in subparagraph 20562-701.630(6)(b)1., 206F.A.C.; July 1, 2013, 210www.gpoaccess.gov/cfr.index.html (212http://www.flrules.org/Gateway/reference.asp?No=Ref-05018214).
215(11) 21640 C.F.R. 261.24 219Table 1-Maximum Concentration of Contaminants for the Toxicity Characteristic; July, 1992.
230(12) GRI Test Method GM13 revision 9 dated June 1, 2009.
241(13) PGI 1104 Specification for PVC Geomembrane, effective April 15, 2008.
252(14) ASTM Method 255D5321/D5321M-14 256“Standard Test Method for Determining 261Shear Strength of Soil-Geosynthetic and Geosynthetic-Geosynthetic Interfaces (ASTM D5321) 270by Direct Shear,” 274January 1, 2014, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, or at www.astm.org/Standard291.
292(15) ASTM Method 295D4716/D4716M-14 296“Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head,” 318(ASTM D4716) January 1, 2014, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, or 335at 336www.astm.org/Standard337.
338(16) ASTM Method 341D5887-09 342“Standard Test Method for Measurement of Index Flux Through Saturated Geosynthetic Clay Liner Specimens Using a Flexible Wall Permeameter,” 362(ASTM D5887) June 1, 2009, 100 Barr Harbor Drive, P.O. Box C700, 374West 375Conshohocken, PA 19428-2959, 378or at 380www.astm.org/Standard381.
382(17) ASTM Method 385D6243/D6243M-13a 386“Standard Test Method for Determining the Internal and Interface Shear Resistance of Geosynthetic Clay Liner by the Direct Shear Method,” 407(ASTM D6243) July 1, 2013, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, or at www.astm.org/Standard426.
427(18) GRI Test Method GM17 revision 6 dated June 1, 2009.
438(19) GRI Test Method GM19 revision 6 dated October 3, 2010. 449http://www.flrules.org/Gateway/reference.asp?No=Ref-01484451. 452This document is also available at 458http://www.geosynthetic-institute.org/grispecs/gm19.pdf.
459(20) ASTM Method D6766-12 463“Standard Test Method for Evaluation of Hydraulic Properties of Geosynthetic Clay Liners Permeated with Potentially Incompatible 479Aqueous Solutions,481” 482(ASTM D6766) July 1, 2012, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, or at www.astm.org/Standard.
501(21) Secondary References. The ASTM Standards contained in subsections 51062-701.210(14), 511(15), (16), (17) 514and (20), 516F.A.C., 517reference 518other 519standards 520that 521are 522listed 523collectively 524below. 525Any 526of 527these 528secondary 529reference 530documents may be obtained at 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, or at www.astm.org/Standard.
549(a) ASTM Method D653-14 “Standard Terminology Relating to Soil, Rock, and Contained Fluids,” August 1, 5652014.
566(b) ASTM 568Method 569D698-12e1 570“Standard 571Test 572Methods 573for 574Laboratory 575Compaction 576Characteristics 577of 578Soil 579Using 580Standard Effort (12,400 ft-lbf.ft3 (600 kN-m/m3)),” May 1, 5902012.
591(c) ASTM Method D1557-12 “Standard Test Methods for Laboratory Compaction Characteristics of Soil 604Using 605Modified Effort (56,000 ft-lbf.ft3 (2,700 kN-m/m3)),” May 1, 6162012.
617(d) ASTM Method D2435/D2435M-11 “Standard Test Methods for One-Dimensional Consolidation 627Properties 628of Soils Using Incremental Loading,” May 1, 6362011.
637(e) ASTM Method D2487-11 “Standard Practice for Classification of Soils for Engineering Purposes (Unified 651Soil Classification System),” May 1, 6572011.
658(f) ASTM 660Method 661D3080/D3080M-11 662“Standard 663Test 664Method 665for 666Direct 667Shear 668Test 669of 670Soils 671Under 672Consolidated 673Drained Conditions,” November 1, 6782011.
679(g) ASTM Method D3740-12a “Standard Practice for Minimum Requirements for Agencies Engaged in 692Testing 693and/or 694Inspection 695of 696Soil 697and 698Rock 699as 700Used 701in 702Engineering 703Design 704and 705Construction,” 707May 7081, 7092012.
710(h) ASTM 712Method 713D4354-12 714“Standard 715Practice 716for 717Sampling 718of 719Geosynthetics 720and 721Rolled 722Erosion 723Control 724Products (RECPs) for Testing,” July 1, 7312012.
732(i) ASTM Method D4439-14 “Standard Terminology for Geosynthetics,” March 1, 7432014.
744(j) ASTM 746Method 747D6243/D6243M-13a 748“Standard 749Test 750Method 751for 752Determining 753the 754Internal 755and 756Interface 757Shear 758Strength of Geosynthetic Clay Liner by the Direct Shear Method,” July 1, 7712013.
772(k) ASTM 774Method 775D4491-99a(2014)e1 776“Standard 777Test 778Methods 779for 780Water 781Permeability 782of 783Geotextiles 784by 785Permittivity,” January 1, 7892014.
790(l) ASTM 792Method 793D5092-04(2010)e1 794“Standard 795Practice 796for 797Design 798and 799Installation 800of 801Groundwater 802Monitoring 803Wells,” August 1, 8072010.
808(m) ASTM 810Method 811D6574/D6574M-13e1 812“Standard 813Test 814Method 815for 816Determining 817the 818(In-Plane) 819Hydraulic 820Transmissivity of a Geosynthetic by Radial Flow,” July 1, 8302013.
831(n) ASTM Method E691-14 “Standard Practice for Conducting an Interlaboratory Study to Determine 844the 845Precision of a Test Method,” April 1, 8532014.
854(o) ASTM 856Method 857D2216-10 858“Standard 859Test 860Methods 861for 862Laboratory 863Determination 864of 865Water 866(Moisture) 867Content 868of Soil and Rock by Mass,” July 1, 8772010.
878(p) ASTM Method D4753-07 “Standard Guide for Evaluating, Selecting, and Specifying Balances and 891Standard 892Masses for Use in Soil, Rock, and Construction Materials Testing,” July 15, 9052007.
906(q) ASTM Method E145-94(2011) “Standard Specification for Gravity-Convection and 915Forced-Ventilation 916Ovens,” December 1, 9202011.
921(r) ASTM 923Method 924D5321/D5321M-14 925“Standard 926Test 927Method 928for 929Determining 930the 931Shear 932Strength 933of 934Soil-935Geosynthetic 936and 937Geosynthetic-Geosynthetic 938Interfaces 939by 940Direct 941Shear,” 943January 9441, 9452014.
946(s) ASTM Method D6072/D6072M-09 “Standard Practice for Obtaining Samples of Geosynthetic Clay 958Liners,” 960January 1, 9622015.
963(t) ASTM Method D5887-09 “Standard Test Method for Measurement of Index Flux Through 976Saturated 977Geosynthetic 978Clay 979Liner 980Specimens 981Using 982a 983Flexible 984Wall 985Permeameter,” 987June 9881, 9892009.
990Rulemaking Authority 992403.061, 993403.704 FS. 995Law Implemented 997403.061, 998403.702-.717 FS. History–New 1-6-93, Amended 1-2-94, Formerly 17-701.210, Amended 5-27-01, 1-6-10, 8-12-12, 2-15-15, 3-13-16.
